-
1 отверстие
hole, opening, orifice, aper-
ture
- в головке торцевого ключа — socket aperture
-, вентиляционное — ventilation /vent/ hole
- глубиной мм — hole... mm deep
-, глухое (несквозное) — blind hole
- для осмотра — inspection hole
- для отбора воздуха — air bleed port
- для отвода (отсоса) пограничного слоя — boundary layer bleed perforation
- для охлаждающего воздуха (в колесе турбины) — cooling air hole (in turbine wheel)
-, дозирующее — metering orifice
-, дренажное (для сообщения с атмосферой) — vent
-, дренажное (на нижней поверхности закрылка) — (flap) drain hole
-, дренажное (приемника воздушных давлений) — (pitot/static tube) drain opening
-, дренажное (сливное) — drain hole, /opening/
-, заправочное — filler (opening)
-, калиброванное — orifice
-, контровочное — locking wire hole
при разрушении (прорыве) контровочного отверстия в гайке, просверлить новое отверстие через соседние грани гайки. — if the locking wire hole is broken, drill a new hole through the nut adjacent flats near the, nut corner.
-, контрольное (в муфте таидера) (рис. 24) — check hole
-, контрольное (уровня масла) — (oil) level hole
-, облегчающее (рис. 10) — lightening hole
-, овальное (фланца магнето) — elongated hole
-, осевое (в ступице турбины) — bore
- отбора воздуха (за pнa внутри корпуса статора кнд) — air bleed perforation /port/
-, отбортованное — beaded hole
- парашюта, полюсное — vent
отверстие в центре купола парашюта. (рис. 105) — an opening, usually in the centre of a canopy.
- подачи воздуха (в смеситель камеры сгорания) — dilution air hole
- подвода воздуха в жаровую трубу — flame tube air hole. air holes around the flame tube section allow air into primary zone of the tube.
- полного давления (приемника воздушных давлений) (рис. 83) — pitot opening used to receive pitot pressure.
-, полюсное (у полюса парашюта), диаметром 12 дюймов — 12-inch diameter vent at apex
-, резьбовое — threaded hole
-, свечное (пд) — spark plug hole
-, свободное — unused hole
-, сквозное — through hole
- слива (отсоса) пограничного споя — boundary layer bleed perforation
-, смотровое — inspection hole
- с резьбой — threaded hole
-, статическое (приемника воздушных давлений) (рис. 83) — static opening. used to receive static pressure.
-, статическое (на бортовых плитах) (рис. 83) — static vent /port/
-, технологическое (испопьзуемое для монтажа, сборки) — production hole
совпадение о. — alignment of holes
- не допускать загрязнения о. — keep the hole clear
переводить о. (со старой детали на новую для сохранения крепежных отверстий на ответной детали) — mark holes on а new unit using the old unit holes as a guideРусско-английский сборник авиационно-технических терминов > отверстие
-
2 смеситель
mixer
- (для смешивания потоков первого и второго контуров гтд) — exhaust mixer. serves to join the exhaust gas arid by-pass air in the exhaust nozzle.
- камеры сгорания — dilution (air) section
air to dilution section passes through dilution air holes.Русско-английский сборник авиационно-технических терминов > смеситель
-
3 изъяны
-
4 полости
-
5 пустоты
2) Engineering: interstices3) Construction: bugholes, pinhole (в бетоне)4) Automobile industry: blowing spaces (в отливках)6) Oil: air holes, interstices (в горных породах), open, openings (в породе), opens, capillary interstices, isolated interstices7) Oil&Gas technology voids8) EBRD: gap (в нормативной базе)9) Makarov: cavings (в боковых стенках формового хлеба; дефект), pore (в породе), pore space (в породе)10) oil&gas: (поры трещины каверны) voids (pores + fractures + vugs) -
6 вентиляционное отверстие
1. vent hole2. air ventРусско-английский военно-политический словарь > вентиляционное отверстие
-
7 относительный объём
Относительный объём-- Z is the feeder holes volume ratio (feeder holes/air film) (... относительный объём питающих отверстий, равный отношению объёма питающих отверстий к объёму воздушной пленки).Русско-английский научно-технический словарь переводчика > относительный объём
-
8 обдувать
blow
- (деталь) сжатым воздухом — blow (а part) with compressed air /air jet/
обдуть деталь сжатым воздухом для удаления пыли и грязи с поверхностей и отверстий. — using an air jet, blow dust and dirt from the surfaces and holes.Русско-английский сборник авиационно-технических терминов > обдувать
-
9 вставлять
•Engage the screwdriver end in the notch.
•Taper shank drills are directly fitted into tapered holes in drilling machine spindles.
•A portion of... is cut away and the release mechanism is interposed.
* * *Вставлять в -- to insert into, to work down, to fit into, to enter into, to engage in; to plug into (о вилке, штекере)Insert the mains plug into the wall socket.Coat the piston with the oil and carefully work down into cylinder bore.Engage the gib head taper key in the keyway.Русско-английский научно-технический словарь переводчика > вставлять
-
10 выпускаться
•Compressed air is allowed to escape from a selected pair of holes.
•Sulphur is released to the atmosphere by sea spray.
•The hot water is released into surface stream flow.
* * *Выпускаться в-- Upon traversing the plate, the flow empties into the test chamber proper.Русско-английский научно-технический словарь переводчика > выпускаться
-
11 вставлять
•Engage the screwdriver end in the notch.
•Taper shank drills are directly fitted into tapered holes in drilling machine spindles.
•A portion of... is cut away and the release mechanism is interposed.
Русско-английский научно-технический словарь переводчика > вставлять
-
12 выпускаться
•Compressed air is allowed to escape from a selected pair of holes.
•Sulphur is released to the atmosphere by sea spray.
•The hot water is released into surface stream flow.
Русско-английский научно-технический словарь переводчика > выпускаться
-
13 нагнетать
•Each pump is capable of delivering (or supplying) 510 tons of water per hour.
•The air was provided by a blower.
Русско-английский научно-технический словарь переводчика > нагнетать
-
14 несколько
•The corresponding pressure ratio is somewhat (or slightly) higher for real gases.
•The temperature changes somewhat when...
•The air pressure must slightly exceed the hydrostatic head.
II. один или несколько•Many clay minerals are composed of more that one (or of several) clay minerals.
•The ability of... to punch multiple holes in one stroke...
Русско-английский научно-технический словарь переводчика > несколько
-
15 нагнетать
•Each pump is capable of delivering (or supplying) 510 tons of water per hour.
•The air was provided by a blower.
Русско-английский научно-технический словарь переводчика > нагнетать
-
16 расходы ... измерялись по отдельности
Расходы... измерялись по отдельности-- Fuel and air were metered separately and injected into the reactor zone through forty small holes.Русско-английский научно-технический словарь переводчика > расходы ... измерялись по отдельности
-
17 соосный
Соосный с-- The optical windows align with three of air-inlet holes corresponding to the primary, secondary, and dilution zones of the combustor.Русско-английский научно-технический словарь переводчика > соосный
-
18 избыток
excess
- веса — excess weight
- воздуха — excess air
- масла — excess oil
high oil level
- мощности — reserve power
- плавучести — reserve buoyancy
- подъемной силы — reserve lift
- смазки — excess grease
excess grease is forced out through the holes.
- тяги — margin of engine thrust
- тяги над сопротивлением — thrust/drag marginРусско-английский сборник авиационно-технических терминов > избыток
-
19 место
space
(в документе, таблице для внесения записей) — the various forms have standardized spaces where the symbols for each day's entry must be placed.
- (расположения, установки агрегата) — location each group of landing lights is installed at a common location.
- агрегата, посадочное (поверхность для установки агрегата) — accessory mounting face fuel pump mounting face is on the wheelcase.
- агрегата, посадочное (специальный прилив с приводом для установки агрегата на двигателе) — accessory (mounting) pad after removing the pump from the engine, blank off the pump pad with a cover plate.
- бедствия (аварии, катастрофы) — area of incident
- бортинженера, рабочее — flight engineer /engineer's/ station
- бортпроводника (кресло в пассажирской кабине, резервируемое для бортпроводника) — cabin attendant /attendant's/ seat
- бортпроводника (специально оборудованное место) — cabin attendant /attendant's/ station
- ввода противопожарных средств (лючок дпя сопла огнетушителя) — fire extinguisher insert point
- ввода противопожарных средств (надпись у лючка для ввода сопла огнетушителя) — fire access
- вертолета (мв) — aircraft position (pos)
- вырубания обшивки — break-in point
место вырубания обшивки фюзеляжа обозначено желтыми углами (рис. 104). — the break-in point on the fuselage is indicated with yellow corner markings.
- вырубания обшивки (надпись) — break in here
- выставки (инерциальной системы) — site of alignment
- выставки (инерциальной системы) в инерциальном пространстве — site of alignment in inertial space
- выставки (инерциальной системы) на земле — site of alignment on earth
- генератора, посадочное — generator mounting pad
- замера (графа таблицы рр) — measurement area
-, исходное (в плане полета по ппм) — origin wpt о may be selected as an origin.
- крепления — attachment point
- командира корабля, рабочее — captain's station
-, критическое (в планере, системе, двигателе) — problem area (in airframe, systern engine)
- ла (самолета, вертолета) — aircraft position (pos)
- ла, определенное методом счисления пути — dead-reckoning position the dead-reckoning position is a combination ofair position and preset wind data.
- ла, штилевое — air position
-, легкодоступное (при техобслуживании) — easily /free/ accessible point /area/
- летного происшествия (аварии, катастрофы) — area of incident
- (нахождения) неисправности (графа таблицы с указанием участка эл. цепи) — possible trouble area
- летчика, рабочее — pilot /pilot's/ station
-, общее (установки) — common location
-, оперативно-доступное (при техобслуживании) — easily /free/ accessible point /area/
- пайки — soldered point
- повышенного внимания (при осмотре и контроле) — thorough-inspection point /area, zone/, point subject to thorough inspection
- под домкрат (рис. 145) — jacking point
- под домкрат (надпись) — jack here
- под козелок (надпись) — trestle here
-, посадочное (на валу) — mounting seat
-, посадочное (поверхность для монтажа агрегата) — mounting face
-, посадочное (специальный прилив для установки агрегата — mounting pad
-, рабочее (в цехе) — workplace (in shop)
-, рабочее (верстак) — workbench
observe absolute cleanliness of workbench, tools and parts.
-, рабочее (члена экипажа) — crew member's station /position/
место члена экипажа на борту ла, специально оборудованное органами управления, приборами, средствами связи и сигнализации, сиденьем или креслом (рис. 88). — the flight crewmembers' stations must be located and arranged so that the flight crewmembers can perform their functions efficiently and without interfering with each other.
- самолета (mс) — aircraft position (pos), fix
точка земной поверхности, над которой в данный момент находится самолет (рис. 122). (cm. местоположение) — in navigation, a relatively accurate ground position of an aircraft determined without reference to any former position.
- самолета, текущее (mс) — present position (pos)
- самолета, текущее, в полете — in-flight present position
-, свободное (в упаковочном ящике) — hollow place /space/ stuff a box with pads to fill out hollow places.
- соединения — connection point
-, спальное — berth
- стоянки — parking area
- стоянки ла (местоположение) — ramp position
- стыка — joint
-, такелажное — lifting point
-, такелажное (надпись) — hoist here
-, труднодоступное — hardly accessible place
- хранения (ч-л. на борту) — stowage
-, центральное — center location
- штурмана, рабочее на м(есте) (в отношении осмотра, изготовления, ремонта) — navigator's station in situ
отсутствие свободного места (в документе дпя внесения записи) — space is crowded if the space is crowded, the entry can be made immediately above the mechanic's signature.
по m(ecту) (об установке) — in place
no месту (напр., сверлить отверстия) — (drill holes) to suit job (requirements)
после занятия рабочих мест в кабине — on entering flight compartment
у рабочего м. (летчика) — at pilot's station
экономия м. (за счет установки малогабаритных агрегатов. блоков) — space saving (by installing small-size units)
занимать м. (в пассажирской кабине) — occupy the seat
занимать центральное м. (о приборах на приб. доске) — be grouped and centered (on panel)
менять места (присоединения) двух проводов — rovers connection of two wires
обнаруживать м. дефекта — locate defect
обнаруживать на шине м. прокола — locate the tire leak point
определять дефект на м. — determine defect in situ
определять критическое м. — detect problem area
перепутать местами (детали при сборке, установке) — misplace
трогаться с м. (о самолете на земле) — move off from rest
устанавливать на м. — install in place
устанавливать на м. (после снятия) — reinstall. steps required to remove and reinstall a component.Русско-английский сборник авиационно-технических терминов > место
-
20 проверка
check (снк), test, inspection
- (раздел рэ) — adjustment/test
-, автономная (инерц. сист.) — self-testing
-, безвыборочная — random check
- биения (радиального) — check for /of/ eccentricity
- биения (скоса боковой поверхности, напр., колеса турбины) — check of swash. checking the swash of turbine wheel.
- введенных координат гпм — waypoint coordinate insertion /entry/ verification
- включения (работы) системы — system operational test
-, внерегламентная — unschedule maintenance check
проверки или осмотры самолета, его систем и агрегатов, проводимые в результате нарушения нормальных условий эксплуатации, независимо от утвержденных сроков проверок, производятся после грубых посадок, в случае удара молний в самолет, посадки с избыточным весом, столкновения с птицей и др. — those maintenance checks and inspection on the aircraft, its systems and units which are dictated by special or unusual conditions which are not related to the time limits. includes inspections and checks such as hard landing, turbulent air, lightning strike, overweight landing, bird strike
- встроенным контролем — built-in test
test the system by using its built-in test facility /ieature/.
-, выборочная — spot check, sampling inspection
-, выборочная (на работоспособность) — spot test
- гермокабины на герметичность — pressurized cabin leakage test
- готовности (ла) к полету — pre-flight check
"- заправки топливом" — fuel oty test (switch) (выключатель)
-, комплексная (систем) — combined systems checkout
-, контрольная — inspection check
- концентричности (колеса турбины, вала) — check of concentricity (of turbine wheel, shaft)
- координат места ла — aircraft position coordinate verification
- ламп — lamp test
- ламп табло (повторным включением) — annunciator lights recall. any reset annunciator lights can be recalled using the warning, caution and advisory lights test switch.
- межпопетная (перед обратным маршрутом) — turnround check
- методом "прокачек" (функциональная проверка электр. цепей) — functional test
- на выявление трещин (одним из объективных методов дефектоскопии) — inspection for cracks (by emplaying an objective method of inspection)
- на герметичность — leak test
-, наземная — ground check
-, наземная (с опробованием) — ground test
- на нспопнитепьном старте — lne-up check
- на магнитном дефектоскопе (на выявление трещин) — magnetic inspection (for cracks)
- на месте (без демонтажа изделия или агрегата с объекта) — in-situ check /test, inspection/. the on-condition check is normally an in-situ test.
- на оправке — check on mandrel
- на правильность формы и взаимного расположения поверхностей (детали) — test for truth
сюда относятся проверки на (не)плоскостность, (не)перпендикулярность, (не)параллельность, овальность и на правильность совмещения отверстий. — the methods for testing for form and alignment are used to check the flatness, squareness, angular relationship or parallelism of the part surfaces, the alignment of holes or the true circularity of round parts.
- на пробой изоляции — insulation breakdown test
- на работоспособность (для подтверждения нормальной работы изделия) — operational test. the procedure required to ascertain only that a system or unit is operable.
- на работоспособность (для подтверждения эксплуатационных характеристик) — operation test. то demonstrate the engine operational characteristics.
- (реакции двигателя) на сброс газа — deceleration test
- на слух — listening test
перебои в работе двигателя могут определяться проверкой на слух, — listening test is employed to determine the engine rough operation.
- на соответствие техническим условиям — functional test
проверка, проводимая с целью подтверждения, что система или агрегат работает в соответствии с минимально допустимыми ту. — the procedure required to ascertain that а system or unit is functioning in all aspects in accordance with minimum acceptable design specifications.
- на стоянке — ramp check /test, inspection/
simple test module provides rapid ramp check.
- на утечку (герметичность) — leak-test
- на утечку мыльной пеной — leak-test with soap suds арplied
coat the pipe with soap suds to detect leakage.
- наличия электрической цепи от...до... — check of electrical circuit between...and...for continuity
- нивелировки (заклинения) неподвижных поверхностей самолета — check of rigging of fixed surfaces
- огнетушителей (без разряда) — fire extinguisher test (firex
нажать кнопку проверка огнетушителей и в этом случае должны загораться лампы 1-я очередь и 2-я очередь срабатывания. — press the firex test button and all main and altn lights illuminate on fire extinguisher test panel.
-, перекрестная (напр., всех аналогичных приборов) — crosscheck (хснеск) crosscheck the three altimeters.
-, периодическая — periodic check
- пиропатронов (противопожарной системы) — squib test. repeat procedure with squib test switch in aft position.
- плоскостности детали на контрольной плите — check for flatness of a part surface against the face of a surface plate
для проведения данной проверки на поверхность кантрольной плиты наносится краска (берлинская лазурь), затем чистая проверяемая поверхность прижимается к контрольной плите. плоскостность проверяемой поверхности, оценивается no наличию отпечатков краски (на выступающих участках). — то make the test, smear the face of the surface plate with marking (consisting of prussian blue or redlead with oil), then wipe clean the sruface to be checked and rub it lightly on the surface plate. the truth of the surface can be estimated by the appearance of the transferred marking.
-, повторная — recheck
- под током /напряжением/ (оборудования, системы) — test /check/ of equipment energized, alive (equipment) test
- по налету — check by flight hour(s)
-по налету, регламентная — periodic /scheduled/ maintenance cheek by flight hour(s)
-, послемонтажная — post-installation check
-, послеполетная — post-flight check
- по состоянию (по мере надобности) — оn-condition check (ос)
профилактическое техническое обслуживание (контроль качества ремонта), выполняемое в виде периодических осмотров, проверок (или испытаний изделия (агрегата), на обнаружение механических дефектов (в доступных пределах) для определения допустимости дальнейшей эксппуатации изделия (до следующей проверки по состоянию). — а failure preventive primary maintenance (overhaul control) process which requires that the item be periodically inspected, checked or tested against some appropriate physical standards (wear or deterioration limits) to determine whether the item can continue its service (for another ос check interval).
- по техническому состоянию — оn-condition check
- по форме "а" ("в", "с"), регламентная (периодиче — scheduled (periodic) "а" ("в", "с") check
- правильности ввода данных — data entry /insertion/ verification
-, предварительная — preliminary check
-, предвзлетная (по контрольной карте) — pre-takeoff check, before-takeoff check
-, предполетная — pre-flight check
-, предпосадочная (по контрольной карте) — pre-landing check, beforelanding check
-, предстартовая — prestart procedure
- приемистости (двигателя) — acceleration test
- прилегания поверхностей на краску (берлинскую лазурь) — check of the surfaces for close contacting indicated by continuity of (prussian blue) marking transferred
-, принудительная (вводимая вручную) — manually initiated /induced/ test /check/
- противообледенительной системы (надпись) — anti-ice test
- противопожарной системы (надпись) — firex test
- работоспособности — operational test
- работы — operational test
- радиального биения (рабочего колеса турбины (на оправке) — check of eccentricity /concentricity/ of turbine wheel (on mandrel)
-, регламентная — scheduled maintenance check
проверки самолета, его систем и агрегатов в указанные сроки. — those manufacturer recommended check and inspections of the aircraft, its systems and units dictated by the time limits.
- самолетов парка, выборочная — sampling inspection of fleet
"- сигнальных ламп" (надпись) — lamp test
- системы — system test (sys tst)
- системы сигнализации пожаpa — fire warning) test
"- системы сигн. пож. в otc. дв. (надпись) — eng compt fire warn test
-, совместная (проводимая поставщиком и покупателем) — conjoint check, check or test conjointly conducted (by supplier and buyer)
- соконусности несущего винта (вертолета) — rotor blade tracking test
- сопротивления изоляции — insulation-resistance test
test for measuring ohmic resistance of insulation.
- с помощью встроенного контроля — built-in test
- с (к-л.) пульта (или наборного поля) — test /check/ via /from/ сапtrol panel (or keyboard)
-, стартовая — on line test
-, стендовая — bench test
-, стендовая (испытание) — bench check/test/
- технического состояния — operational status check, check for condition
-, транзитная — transit check
план транзитного полета включает транзитную проверку. — the transit time schedule includes transit check.
-, тщательная — thorough check
-, функциональная — functional test
- электрической прочности (изоляции) — (insulation) voltage-withstand test
проверка способности изоляции выдерживать (повышеннoe против нормы) напряжение. — application of voltage (higher than rated) for determining the adequancy of insulation materials against breakdown.
- элементов конструкции (ла), выборочная — structural sampling test
- эффективности системы охлаждения (двигателя и редуктора вертолета) при взлете (висении, наборе высоты, снижении) — takeoff (hovering, climb, descent) cooling test
'включение проверки' (надпись) — test on
причина п. — reason for check /test/
производить п. по 3, пп. a,6 — test the unit according to requirements of para. 3 (a, b)Русско-английский сборник авиационно-технических терминов > проверка
- 1
- 2
См. также в других словарях:
Air Jordan — Not to be confused with Jordanian Airlines. The Jumpman logo is used by Nike to promote the Air Jordan brand. Air Jordan(s), also known simply as Jordans, are a brand of shoes and athletic apparel produced by Nike originally designed for and… … Wikipedia
Air France Flight 447 — F GZCP, the aircraft involved in the accident Accident summary Date 1 June 2009 … Wikipedia
Air-raid shelter — in Tateyama[disambiguation needed … Wikipedia
Air hockey — is a game for two competing players trying to score points in the opposing player s goal. EquipmentAir hockey requires an air hockey table, two mallets, and a puck.A typical air hockey table consists of a large smooth playing surface, a… … Wikipedia
Air pressurized water — extinguishers or APW are types of fire extinguishers that extinguish burning material by absorbing heat . They contain 2.5 gallons of water or water with a wetting agent which is applied by means of a 1/2 inch hose with a smooth bore nozzle… … Wikipedia
Air flow ball — Air flow balls are small, plastic balls, often used in physical training because of their many parallel holes, which help reduce backspin and increase drag, thus hampering the ability to travel long distances. Also, the light plastic shell cuts… … Wikipedia
air-brick — airˈ brick noun A block with holes for ventilation • • • Main Entry: ↑air … Useful english dictionary
Air well (condenser) — High mass air well of Belgian engineer Achile Knapen in Trans en Provence … Wikipedia
air-cushion machine — ▪ vehicle Introduction also called ground effect machine, or hovercraft, any of the machines characterized by movement in which a significant portion of the weight is supported by forces arising from air pressures developed around the… … Universalium
Air conditioner — For general aspects of air conditioning, see Air conditioning. A typical home air conditioning unit. An air conditioner (often referred to as AC) is a home appliance, system, or mechanism designed to dehumidify and extract heat from an area. The… … Wikipedia
Air traffic control — For the Canadian musical group, see Air Traffic Control (band). Airport Traffic Control Towers (ATCTs) at Amsterdam s Schiphol Airport, the Netherlands … Wikipedia